WLAN Wireless Ethernet Bridge inklusive Repeater?!

hitzkopf

kennt sich schon aus
Guten morgen,

ich hab mal eine Frage.
Bei stellt sich folgendes Problem dar:
In einem Wireless Netzwerk wird der Internetzugang über einen Linksys Cisco WRT160N V3 realisiert. Alle sind per Wlan mit dem Router verbunden. Da sich keine Kabel zum Router ziehen lassen. Nun muss ich in dieses Netzwerk einen Netzwerkdrucker installieren per RJ45 :cry:
In meiner Voreile habe ich dann einen zweiten Linksys Cisco WRT160N (allerdings V2) gekauft, in der Hoffnung es funktioniert.
Aber die zwei WLAN Router lassen sich nicht miteinander verbinden. Keiner kann WDS. :mad
Nun meine Frage:
Kann mir einer eine Kaufempfehlung geben?
Ich suche quasi eine Wireless Ethernet Bridge, welche auch als Repeater fungiert. Weil die Reichweite soll in einem mit erweitert werden.
Vielen Dank im Voraus.
Gruß Computerhitzkopf
 

74min

fühlt sich hier wohl
hi,

ich kann dir nicht mit den bunten kleinen Fertig-Kisten aus dem Regal in 4 Farbprospekt und gekauften 300 Testberichten dienen - habe mich jahrelang damit herumgeärgert.

Von meiner Seite nur der Tipp: baue dir das selbst, wie du es benötigst: bspw mit sheeva plug oder guru plug server, ca 75 euro:
GuruPlug Server

hth
74min
 

Lektro

assimiliert
Ich habe bei mir einen TP-Link TL-WA901ND (ca. 40€) im Einsatz.

Demo gibt es hier: http://www.cormain.com.au/demo/TPTLWA901ND/default.htm

Der Client- oder auch der Bridge-with-AP-Mode sollte für dein Vorhaben passen:
Operation Mode - Several Operation Modes are supported, including: (1)Access Point (2)Multi-SSID (3)Client (4)Repeater (5)Universal Repeater (6)Bridge with AP. The available setting options are different in various operation modes, and they are explained below.

Access Point - This operation mode allows wireless stations to access.

Multi-SSID - AP can support up to 4 SSID.

* Enable VLAN - Check this box to enable the VLAN function. The AP supports up to 4 VLANs. All wireless PCs in the VLANs are able to access this AP. The AP can also work with an IEEE 802.1Q Tag VLAN supporting Switch. If this Switch enables the Tag VLAN function, besides all wireless PCs, only the PCs in the VLAN same with SSID1 are able to access the AP. If a PC is directly connected to the LAN port of the AP, please make sure that its adapter supports Tag function, or this PC will not be able to access the AP.
* SSID - Enter a value of up to 32 characters. The same Name (SSID) must be assigned to all wireless devices in your network. In Multi-SSID operation mode, enter SSID for each BSS in the field "SSID1" ~ "SSID4".
* VLANID - The ID of a VLAN. Only in the same VLAN, can a Wireless PC and a wired PC communicate with each other. The value can be between 1 and 4095. If the VLAN function is enabled, when AP forwards packets, the packets out from the LAN port will be added with an IEEE 802.1Q VLAN Tag, whose VLAN ID is just the ID of the VLAN where the sender belongs.
* Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the AP can be used. It may be illegal to use the wireless function of the AP in a region other than one of those specified in this filed. If your country or region is not listed, please contact your local government agency for assistance.
* Channel - This field determines which operating frequency will be used. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point.
* Mode -This field determines the wireless mode which the AP works on.
* Channel Width - The bandwidth of the wireless channel.
* Max Tx Rate - You can limit the maximum tx rate of the AP through this field.
* Enable Wireless Radio - The wireless radio of the AP can be enabled or disabled to allow or deny wireless stations to access. If enabled, the wireless stations will be able to access the AP, otherwise, wireless stations will not be able to access the AP.
* Enable SSID Broadcast - If you select the Enable SSID Broadcast checkbox, the AP will broadcast its name (SSID) on the air.

Client - This device will act as a wireless station to enable wired host(s) to access AP.

* Enable WDS - The AP client can connect to AP with WDS enabled or disabled. If WDS is enabled, all traffic from wired networks will be forwarded in the format of WDS frames consisting of four address fields. If WDS is disabled, three address frames are used. If your AP supports WDS well, please enable this option.
* SSID - Enter the SSID of AP that you want to access. If you select the radio button before SSID, the AP client will connect to AP according SSID.
* MAC of AP - Enter the MAC address of AP that you want to access. If you select the radio button before MAC of AP, the AP client will connect to AP according MAC address.


Repeater - In Repeater mode, the AP with WDS enabled will relays data to an associated root AP. AP function is enabled meanwhile. The wireless repeater relays signal between its stations and the root AP for greater wireless range. Please input the MAC address of root AP in the field "MAC of AP".

Universal Repeater - In Universal Repeater mode, the AP with WDS disabled will relays data to an associated root AP. AP function is enabled meanwhile. The wireless repeater relays signal between its stations and the root AP for greater wireless range. Please input the MAC address of root AP in the field "MAC of AP".

Bridge with AP - This operation mode bridges the AP and up to 4 APs also in bridge mode to connect two or more wired LANs. Please input the MAC address of other APs in the field "MAC of AP1" to "MAC of AP4". AP function will also startup.
 
Zuletzt bearbeitet:
Oben